Cheap Street rules *updated 7-15-09*
Moderators: mokangena, DN, scottab, Carl Blanton
- Carl Blanton
- Senior Weasel
- Posts: 1797
- Joined: Mon Jun 06, 2005 6:00 pm
- Contact:
Cheap Street rules *updated 7-15-09*
Cheap Street is a entry level class Craig has cooked up for heads up racing at Mo-Kan. It will run with some special races and it will run on a few Friday nights, basically once a month.
This class will be all run on a Pro ladder with one round of qualifying. Cheap street will run 1/4 mile, subject to review and change.
The rules;
Engine:
Any automotive internal combustion engine allowed
Must be stock manufacturer block
No aftermarket blocks
Conventional heads must be run on all engines
Transmission:
Any automotive transmission allowed
Transbrake Allowed
Electronics:
Progressive Nitrous Controller Allowed
2-step Allowed
No Delay Box
Power Adders:
BB V8 must run N/A
One power adder for SB V8/6 cylinder
Single stage nitrous
No multi-port nitrous fogger
Single 76 mm Turbo
No Twin Turbos
Centrifugal Superchargers limited to: Procharger D-1 or smaller
• Vortec V3 or smaller • Any Paxton or Powerdyne
2.8 or smaller Kenne Bell and 3.4 and smaller Whipple blowers
6-71 or Smaller roots blower allowed
Any Intercooler Allowed
No Methanol or Water Injection
4-cylinder unlimited power adders
Fuel:
All cars must run on gasoline (Except for N/A small block may run
methanol)
No Nitromethane
Tires:
275/60-15 or smaller drag radial
28x10.5-15 (non-w) or smaller Slick
Street radials limited to 275 or narrower
Chassis:
Bolt in Suspension parts only
Ladder bars allowed
Coilovers allowed
Minitub allowed
Inner frame rail must remain in stock unmodified position
Stock firewall and floor pan must remain in unaltered position
Subframe Connectors allowed
Body:
Must be stock appearing factory built body
Functioning Mufflers required
No cutouts
Headlights, taillights must function
Fiberglass limited to hood, decklid and bumpers (unless stock)
Full interior (rear seat may be removed, but area must be carpeted)
No Lexan (except back window in trucks for roll bar)
Mo-Kan Safety rules apply.
Subject to review and change.
Civil comments welcome.
This class will be all run on a Pro ladder with one round of qualifying. Cheap street will run 1/4 mile, subject to review and change.
The rules;
Engine:
Any automotive internal combustion engine allowed
Must be stock manufacturer block
No aftermarket blocks
Conventional heads must be run on all engines
Transmission:
Any automotive transmission allowed
Transbrake Allowed
Electronics:
Progressive Nitrous Controller Allowed
2-step Allowed
No Delay Box
Power Adders:
BB V8 must run N/A
One power adder for SB V8/6 cylinder
Single stage nitrous
No multi-port nitrous fogger
Single 76 mm Turbo
No Twin Turbos
Centrifugal Superchargers limited to: Procharger D-1 or smaller
• Vortec V3 or smaller • Any Paxton or Powerdyne
2.8 or smaller Kenne Bell and 3.4 and smaller Whipple blowers
6-71 or Smaller roots blower allowed
Any Intercooler Allowed
No Methanol or Water Injection
4-cylinder unlimited power adders
Fuel:
All cars must run on gasoline (Except for N/A small block may run
methanol)
No Nitromethane
Tires:
275/60-15 or smaller drag radial
28x10.5-15 (non-w) or smaller Slick
Street radials limited to 275 or narrower
Chassis:
Bolt in Suspension parts only
Ladder bars allowed
Coilovers allowed
Minitub allowed
Inner frame rail must remain in stock unmodified position
Stock firewall and floor pan must remain in unaltered position
Subframe Connectors allowed
Body:
Must be stock appearing factory built body
Functioning Mufflers required
No cutouts
Headlights, taillights must function
Fiberglass limited to hood, decklid and bumpers (unless stock)
Full interior (rear seat may be removed, but area must be carpeted)
No Lexan (except back window in trucks for roll bar)
Mo-Kan Safety rules apply.
Subject to review and change.
Civil comments welcome.
Re: Cheap Street rules
Sounds like a cool class.
![Lay Rubber :layrubber:](./images/smilies/3rdgear.gif)
![Lay Rubber :layrubber:](./images/smilies/3rdgear.gif)
![Lay Rubber :layrubber:](./images/smilies/3rdgear.gif)
-
- Posts: 266
- Joined: Wed Apr 09, 2008 5:31 pm
Re: Cheap Street rules
I LOVE the Cheap Street Class. Might get something going for that, too.
P/M Blown Corvette
VP - National Progressive TaeKwon Do Association
VP - National Progressive TaeKwon Do Association
Re: Cheap Street rules
Is there any exception on these rules?Like if it was a SBC and it was N/A. I have a Sbc Rodeck aluminum block and Brodix Canted Valve Heads but it is only 410ci.JasonMust be stock manufacturer block
No aftermarket blocks
Conventional heads must be run on all engines
JASON ULVEN
Your local Hoosier Dealer
417-733-4936
Thanks to Sponsors
WorkTurbochargers
Neal Chance Converters
Your local Hoosier Dealer
![Image](http://www.hoosiertire.com/Logohrt.jpg)
417-733-4936
Thanks to Sponsors
WorkTurbochargers
Neal Chance Converters
Re: Cheap Street rules
does the exhaust need to exit in the rear or will it pass as long as there is a muffler there?...say a downpipe dumped with a bullet style muffler?
never bring show to a go fight...
- bad355_67camaro
- Posts: 501
- Joined: Tue Jun 14, 2005 4:50 pm
Re: Cheap Street rules
i'm kind of doubting it. The rules are intended to keep it "budget" oriented and a stock block, in some cases, can be a limiting factor on how fast the field is.julven wrote:Is there any exception on these rules?Like if it was a SBC and it was N/A. I have a Sbc Rodeck aluminum block and Brodix Canted Valve Heads but it is only 410ci.JasonMust be stock manufacturer block
No aftermarket blocks
Conventional heads must be run on all engines
New build for 2015
Thanks to our 2015 sponsors
http://www.timsbodyandglass.com
Bentune Performance & Fabrication
Performance Coatings (417)439-0546
C&R Transmission (417)736-2191
C&S Specialties Fuel Systems (636) 723-4996
5.30@135
8.36@167
Thanks to our 2015 sponsors
http://www.timsbodyandglass.com
Bentune Performance & Fabrication
Performance Coatings (417)439-0546
C&R Transmission (417)736-2191
C&S Specialties Fuel Systems (636) 723-4996
5.30@135
8.36@167
- mokancraig
- Mo-Kan Webmaster
- Posts: 1090
- Joined: Wed Jun 01, 2005 7:42 am
- Location: Asbury, MO
Re: Cheap Street rules
Correct, the idea was to keep the more expensive/exotic parts out of this class.
Durty, no restrictions on how much exhaust. Just that there is a functioning muffler.
Durty, no restrictions on how much exhaust. Just that there is a functioning muffler.
Craig
Re: Cheap Street rules
I am with you on the budget part and that is why I built what I have. Mine is just some old used sprint car stuff that cost the same to build as most N/A aluminum headed big block Chevy w/stock blocks in my eyes. But because it is what it is aft and aluminum I am willing to take the biggest handicap. N/A only. And let’s say I was to win one and Carl and Craig didn't feel it was fair I won't run the class again. But I said Carl and Craig because we all know there is always haters. Jasonbad355_67camaro wrote:i'm kind of doubting it. The rules are intended to keep it "budget" oriented and a stock block, in some cases, can be a limiting factor on how fast the field is.julven wrote:Is there any exception on these rules?Like if it was a SBC and it was N/A. I have a Sbc Rodeck aluminum block and Brodix Canted Valve Heads but it is only 410ci.JasonMust be stock manufacturer block
No aftermarket blocks
Conventional heads must be run on all engines
JASON ULVEN
Your local Hoosier Dealer
417-733-4936
Thanks to Sponsors
WorkTurbochargers
Neal Chance Converters
Your local Hoosier Dealer
![Image](http://www.hoosiertire.com/Logohrt.jpg)
417-733-4936
Thanks to Sponsors
WorkTurbochargers
Neal Chance Converters
- Carl Blanton
- Senior Weasel
- Posts: 1797
- Joined: Mon Jun 06, 2005 6:00 pm
- Contact:
Re: Cheap Street rules
No exceptions at this time.
We need to run this class a few times, sticking to the letter of the rule, before we look at any changes.
We need to run this class a few times, sticking to the letter of the rule, before we look at any changes.
Re: Cheap Street rules
Sounds good.If things change let me know.We still have another car in the family that fits the rules so we will be there.
JASON ULVEN
Your local Hoosier Dealer
417-733-4936
Thanks to Sponsors
WorkTurbochargers
Neal Chance Converters
Your local Hoosier Dealer
![Image](http://www.hoosiertire.com/Logohrt.jpg)
417-733-4936
Thanks to Sponsors
WorkTurbochargers
Neal Chance Converters
Re: Cheap Street rules
Are bowtie blocks or Fords sportsman blocks considered production blocks? Just noticed the tags and insurance rule is there a reason for this rule .I for one have never tagged or insured any race car just because i dont typically drive them on the street just curious.
5.25@137 On 275's
Re: Cheap Street rules
im sure its cause its the Cheap Street class
never bring show to a go fight...
Re: Cheap Street rules
durty wrote:im sure its cause its the Cheap Street class
Just because you have tags and Insurance on your race car doesn't make it a "street car". The rules will limit the cars performance not tags and insurance .The only thing that rule does is add more money to the cost of racing .
5.25@137 On 275's
Re: Cheap Street rules
Mine has Classic plates and Insurance and has seen lots of street time in it's life.Like VAMP it is just another way to make it more street car oriented I would say but it doesn't wake one a street car .
JASON ULVEN
Your local Hoosier Dealer
417-733-4936
Thanks to Sponsors
WorkTurbochargers
Neal Chance Converters
Your local Hoosier Dealer
![Image](http://www.hoosiertire.com/Logohrt.jpg)
417-733-4936
Thanks to Sponsors
WorkTurbochargers
Neal Chance Converters